全部

1·It can be reasonable combined according to the blowing rate to meet the actual demand.

该设备还可根据处理风量大小合理组合，以满足实际需要。

2·In the operation of jigging machine, we should timely adjust blowing rate, water quantity, feeding and layout.

在跳汰机的作业的操作中，要适时调节风量、水量、给料和排料。

3·The influence of contents of blowing agent AK on the curing rate, blowing rate of silicone rubber were discussed.

研究了发泡剂AK用量对硅橡胶硫化速率和发泡速率的影响。

4·The reasonableness and practicability of way direct to monitor the blowing rate of axial fan have been verified in the article.

对电厂动调轴流式风机，用运行风量直接监测方法的合理性与可行性进行了论证。

5·This article focuses on technical issues such as feeding, blowing rate, water quantity, feeler lever and layout quantity of jigging machine.

本文主要阐述了跳汰机的给料、风量和水量、探杆、排料量等技术问题。

6·Experiment results show that gas phase made silicon dioxide performs an important function in increasing the blowing rate of PVC paste resin.

实验表明， 气相法二氧化硅对提高聚氯乙烯糊树脂的发泡倍率起着重要作用。

7·There were optimum matching of top blowing rate and bottom blowing rate and corresponding location during top-bottom blowing to get better effect.

顶底复吹时，为取得较好的效果，亦存在顶吹-底吹气量的最佳配合及相应的有利位置。

8·The smelting process was strengthened by using high top pressure, high pressure drop, large blowing rate, reduced tuyere section and enhanced blasting velocity.

采取高顶压、高压差、大风量、缩小风口直径、提高风速和鼓风动能等措施进一步强化冶炼；

9·Discussion focus on the influences of technological parameters like spinning temperature, spinning speed, blowing rate, oil finishing as, well as texturing on the products quality.

重点讨论了纺丝温度、纺丝速度、侧吹风风速、上油、拉伸变形等工艺参数对产品质量的影响。

10·The experiment result of the sintered metal tube shows that the uneven rate of axial blowing is lower than 10%, and the flow is steady.

烧结金属筒实测结果显示，吹风径向不匀率小于10%，且气流稳定。

风量

1·The reasonableness and practicability of way direct to monitor the blowing rate of axial fan have been verified in the article.

对电厂动调轴流式风机，用运行风量直接监测方法的合理性与可行性进行了论证。

2·In the operation of jigging machine, we should timely adjust blowing rate, water quantity, feeding and layout.

在跳汰机的作业的操作中，要适时调节风量、水量、给料和排料。

3·The smelting process was strengthened by using high top pressure, high pressure drop, large blowing rate, reduced tuyere section and enhanced blasting velocity.

采取高顶压、高压差、大风量、缩小风口直径、提高风速和鼓风动能等措施进一步强化冶炼；

4·This article focuses on technical issues such as feeding, blowing rate, water quantity, feeler lever and layout quantity of jigging machine.

本文主要阐述了跳汰机的给料、风量和水量、探杆、排料量等技术问题。

5·It can be reasonable combined according to the blowing rate to meet the actual demand.

该设备还可根据处理风量大小合理组合，以满足实际需要。